Hellfire 2206 2200Kv Brushless Motors Review

0
4055

RadioC sent us some Hellfire 2206 2200kv motors to test out. How do these £14 motors compare to the more expensive Cobra motors with similar specs? Let’s find out.

Motors came in two boxes, all with clockwise shaft threads. Along with motors there are 16 x M3 mount screws. They are suitable for mounting motors on 3mm and 4mm arms.

 

Motor coils is bright red, which isn’t commonly seen in other motors we have reviewed. Coils are wound very nicely almost like it was done by hand (maybe it was but not confirmed).

Hellfire 2206 comes with uncut motor wires which are long and weight 34g each. After cutting the wires to about 3cm, the weight goes down to 28g which is pretty standard weight for 2206 motors. Cobra 2206 2100kv for instance weights 29g with the same length of wires.

Comparison with Cobra 2204 and 2206 motors: Hellfire has shorter motor shaft than the Cobra’s (Hellfire: 11mm vs Cobra: 14mm).

Hellfire 2206 2200KV Motor compared to cobra 2204 2206 2000kv

Thrust

2206 motors can generally generate more torque than the 2204 motors, as well as having slightly lower KV, it makes perfect sense to put 6 inches propellers on this motor. The extra motor weight is compensated by the additional thrust generated from the larger props.

I don’t have a thrust stand so I cannot run the thrust tests myself. However RadioC did the testing and I am sharing it here.

According to this motor thrust test, Hellfire motor with HQ 6045 on 4S battery can generate around 1300g of static thrust @ 100% throttle. In real flying situation that number will be smaller, but with over 1Kg of thrust per motor – still a very impressive figure.

Testing

I am testing the Hellfire motors on my EVO250 frame. Previously I used Cobra 2206 2100kv motors on this quad.

Also I swapped out all the supplied prop nut with nyloc nuts (Nylon Insert Lock Nut). From my experience, they hold better and doesn’t come loose during flight or even in crashes.

Testing setup:

Frame: EVO250 (DemonRC.eu)
Motors: Hellfire 2206 2200kv
ECS: Rotorgeeks RG20A BLHELI 14.3
Flight Controller: Dodo with Betaflight 2.3.4
Battery: 4S
Props: HQ 6×3.5 / HQ 6×4.5
FPV Setup: Sony PZ0420 FPV camera + Dominator V2 + 600mw ImmersionRC
Recording camera: GoPro 3+ Black
PID Controller 1 – Rewrite
Flying experience with these motors was great. Due to the slightly higher KV spec, I feel like they have a little bit more power than Cobra 2206 2100KV. HQ 6×4.5 props are not a problem for the Hellfire’s. Tons of thrust and snappy response.

Flying a 6 inches quads always gives me a more floaty feeling, certainly not as agile and nimble as a 5 inches mini quad. But still with the amount of thrust generated, racing, or acro freestyle are not a problem.

After changing props few times I noticed that the thread on one of the motors was wearing out more than the others. This is something I have never had on Cobras. Looks like material used for the bell and shaft is softer.

Shaft is shorter as I mentioned and the Nyloc bolt can only go in half way. With the HQ 6035 props the nyloc nut can go deeper because the props hub is thinner.

Motor durability test was done in a very harsh conditions: Frozen ground and stones at the race course. I had quite a few crashes (even managed to damage the carbon fibre on my frame) and had mid air collisions with another mini quad (not my fault 🙂 ). Only a few scratches.

I didn’t notice any vertical play on the shaft, that usually happened with Cobra after few crashes. The bell was still in their initial position.

Final thoughts

What we like:

Cheaper price, at £13.98 per motor
Resistant to crashes
Nice look (I like the red a lot!)
powerful with 6? prop

What could be changed:

Longer motor shaft for propeller mounting
Use stronger/harder material for the motor bell and shaft
Replace prop nuts with Nyloc nuts

We would like to thank Radioc.co.uk for giving us the Hellfire motors.

NO COMMENTS